An Industry Leader for over 20 Years
  • CONTACT US
  • FAQ
Injector-Rehab Injector-Rehab
Select category
  • Select category
  • Bulk Components
  • Connectors & Adapters
  • Filters
  • GDI & Piezo Components
  • Grommets and Other
  • Injector Cleaning
  • Injector Cleaning Supplies
  • KGParts Products
    • BMW Motorcycle
    • Mazda RX7 Top Feed Fuel Rails
      • Mazda RX8
      • Other Rotary
      • RX7 86-91 (FC)
      • RX7 93+ (FD)
    • Misc KGParts Items
    • Pro-Jay Intake Manifolds
    • VW Fuel Systems
  • New Injectors
  • O-Rings
  • Pintle Caps
  • Rebuild Kits
  • Refurbished Injectors
    • Automotive
    • Marine Injectors
    • Nissan Re-Coiled JECS
Login / Register
0 items $0.00
Menu
Injector-Rehab Injector-Rehab
0 items $0.00
Browse Categories
  • Injector Cleaning
  • Pintle Caps
  • O-Rings
  • Filters
  • Grommets and Other
  • GDI & Piezo Components
  • Rebuild Kits
  • Connectors & Adapters
  • Bulk Components
  • Injector Cleaning Supplies
  • Injectors
    • New Injectors
    • Refurbished Injectors
      • Automotive
      • Marine Injectors
      • Nissan Re-Coiled JECS
  • KGParts Products
    • VW Fuel Systems
    • BMW Motorcycle
    • Mazda RX7 Top Feed Fuel Rails
      • Mazda RX8
      • Other Rotary
      • RX7 86-91 (FC)
      • RX7 93+ (FD)
    • Misc KGParts Items
    • Pro-Jay Intake Manifolds
  • Home
  • Core Rewards
  • Shop
  • Knowledge Base
    • Injector Cleaning
      • Fuel Injector Cleaning and Flow Testing Service
      • Standard Fuel Injector Cleaning and Flow Testing
      • Dynamic Testing and Cleaning Fuel Injectors
      • GDI Fuel Injector Cleaning & Testing
      • Rebuilding a Piezoelectric Fuel Injector
      • Piezoelectric Fuel Injector Cleaning
      • Service Instructions
      • Reading GDI Service Reports
    • Basic Information
      • Videos
      • Glossary of Terms
      • Troubleshooting and Cleaning Fuel Injectors
      • Common Problem Injectors
      • Supra vs Walbro
      • An E85 Breifing
      • AN Fitting and NPT Threads
      • Fuel Pulsation Damper
      • Fuel Injector Cleaning & Gas Mileage
    • Technical Information
      • Fuel Injector Lag Times
      • Fuel Injector Flow Rates
      • Fuel Injector Duty Cycle
      • Injector Drivers
      • Selecting the Correct Resistors
      • MAP Sensors
      • How A Fuel Injector Works
      • Fuel Pump Test and Drivability Issues
      • E85 Injector Sizing
      • Published Fuel Injector Data
    • Calculators / Conversions
      • Fuel Injector Max Capacity
      • Fuel Injector Size Selection
      • Fuel Pressure Modification
      • Fuel Injector Conversion – cc/min to lbs/hr
  • FAQs
  • Fuel Injector Application Guide
Piezoelectric Injector Testing
Click to enlarge
Home Injector Cleaning BMW N54 N63 N74 Injector Cleaning and Flow Testing
optimax air injector
Mercury OptiMax Outboard Black Air Injector (Each) $199.00
Back to products
Bosch GDI Filter
Bosch GDI 4.5 x 3 x 17mm Filter $0.89

BMW N54 N63 N74 Injector Cleaning and Flow Testing

$39.00

To expedite your order, please Include your Make, Model, Year and Engine size in the Notes section at checkout **

Turnaround time on Piezoelectric Injectors is currently 14 – 21 days from receiving. Understand that this is NOT a quick process. We work as quickly and thoroughly as possible. If you are the customer who will be contacting us every other day for an “Update”, please DO NOT even purchase this service.

***PLEASE READ***

We are THE Authority on BMW & Mercedes Piezo Injector Cleaning. However, you need to understand some of what we know. Click the link below!
Make sure you understand the expectations of having this service done.

This item includes service for ONE Piezoelectric injector Injector. Please set the quantity to the number of injectors you need serviced. We have a 2 injector minimum. There are NO refunds on injectors that have failed testing or counterfeit. See link above about expectations.

 

Service with Injector-Rehab for a Piezoelectric Injector WILL test your injector at the actual operating pressure unlike most every other company that claims they can service them. Others will claim that they can service them on their port injection machines with an adapter to be able to drive the injector electronically. This is a partial truth. They may be able to drive the injector and see a spray pattern at lower pressures, but this does NOT tell them the information they need to determine if an injector is actually good.

Piezoelectric injector testing is a far cry from standard port / PFI injector testing. GDI systems have various ways to trigger their injectors and do so at varying pressures. In other words, the varying pressure at the rails varies on demand. By definition, this means the electrical conditions will be varying as well. On a standard PFI system, the pressure remains the same at a steady 35psi – 60psi depending on the system. Nominal PFI injectors draw about 900 milli Amps where GDI Injectors use a Peak-and-Hold Triggering scheme much like the older Throttle Body Injectors. The biggest difference is the voltage and current values employed. GDI internal resistance ranges between 2.6 to 16.3 Ohms, depending on the application. Next, we will explain how GDI Injectors are triggered and how we test them.

The analysis of the waveform of the injectors allows us to read how the injector is operating through a built in oscilloscope on the flow bench that analyzes the wave form. Each Injector’s current waveform has a few points of interest.

One is the injector “turn-on” point. This turn-on point can go as high as 12 amps. This all depends on fuel demands of the particular engine conditions. The turn-on current value will change according to demand. You also need to remember that a GDI open event is much faster than a standard port injection at about 0.04 to 5 milli seconds. Standard PFI has an injector lag time of around 5 to 15 (or higher) milli seconds.

Two is the first stage of the hold current. The idea behind Peak-and-Hold is to supply a high current to quickly activate or open the injector needle. Being that GDI pressures are A LOT higher, you need a lot more current to open, hence the high 12 Amp value. Once it is open, in order to protect the internal coil, once it is opened the current is reduced down by internal ECM resistor to about 5 Amps.This allows the injector to stay open to the exact same aperture as before or during the 12 Amp current spike, but with less heat.

Three is the second stage in the hold current which is set at about 2.5 Amps. Not all GDI systems have this second hold stage. If they do, it is there to further protect it from heat damage. If available, it is deployed when the injector opening reaches the higher values, or above 3.5 milli seconds.

Testing a GDI Injector PROPERLY is no easy mater due to the fact that their operating conditions of of current voltage and pressure are ALWAYS changing. By running an injector in it’s actual conditions is the ONLY way to properly test the condition of the injector. An electrical and pressure “stress test” is required to get the injector ready for testing. Injectors do not fail when initially tested, they fail under “heat”, which can not be replicated without running under the operating conditions.

Companies using a standard port injection machine 100% absolutely CAN NOT do this. Because they can’t, they claim they can see the spray pattern better at low pressures and at static flow. THIS IS FALSE. If you were in the injector business and couldn’t test under actual operating conditions, would you come up with a believable “Excuse” (We will call it), or would you just miss out on all that business? Unfortunately many many places decide to tell their customers this “Excuse”.

Service to include the following:

(optional) Regenerating Piezo Stack

3 Step Cleaning Process

3 Stage High Pressure Leak Down Test

Back-Flushing Injectors

(Optional) Nozzle Response Test

Internal Lubrication

Actuator Capacitor Test

Injector Numbering

Nozzle Leak Down Test (Low and High Pressure)

Individual Bagging

7 Stages of Interval Metering Testing

Comprehensive Flow Report

Replace all Serviceable Parts (Optional)

 

 

For a help understanding the reports you will receive after service, CLICK HERE Understand the reports you receive via email are the AFTER results. We do not test a “before” service due to the amount of time running a test plan takes. Turnaround time would be double. We assume any injectors we receive needed service and cleaning.

This item is for Siemens VDO Piezoelectric Injectors, tested AT Actual Operating Pressure. This is ONLY meant for Index 11 or Index 12 Injectors. Sending in Earlier revisions you should NOT expect the service to fix design flaws of earlier versions. You WILL be disappointed if you are attempting to have this service fix an issue that is an earlier design flaw.

 

In stock

New Combustion Seal and Decoupler *

Replace and install the Combustion Seal and Decoupler with New

Regenerate Piezo Stack *

Regenerating the Piezo Stack is the equivalent of resetting the memory of a battery. Your Injectors forget the full range they are capable of operating due to driving habits. Regenerating the stack is highly recommended and can fix many drivability issues in your BMW.

Nozzle Response (Lag time) Report Per Injector *

Response Time (Lag time / latency) report for each injector individually for tuning purposes

Skip the Line Service

Purchasing this service will ensure that your set of injectors are serviced before all other sets that arrive the day your package arrives.
Injectors will still be shipped back with standard shipping. !! MARK OUTSIDE OF PACKAGE “Skip the Line” !!
!! This is NOT a guarantee for Same Day Service !!

Return Shipping Insurance

For each $100 in insurance you want, add $2 to the total. As an example, if the replacement for your injectors is $500, then you should make the total 10. Do not insure something that can be replaced for $500 with $3000 worth of insurance. In the rare event that a claim would need to be filed, the burden of proof will be on you. We are simply placing the insurance on the item you are having us send back to you.

SKU: CleanFlow-Piezo-BMW Category: Injector Cleaning
Share:

You may also like…

Injector Flow Bench
Add to cart
Quick view

Dynamic Cleaning

SKU: Dynamic-Cleaning
$25.00
Injector Flow Bench
Add to cart
Quick view

Flow Only

SKU: Flow-Only
$10.00
F225 Injector
Add to cart
Quick view

Yamaha F225 Outboard Injector

SKU: RM-Yam225
$39.00

Related products

Injector Flow Bench
Add to cart
Quick view

Standard Fuel Injector Clean and Flow Test

SKU: CleanFlow
$18.00
Optimax Air Injector Service
Select options
Quick view

Optimax Air Injector Cleaning and Flow Testing

SKU: CleanFlow-OPTAIR-Serv
$18.00
Side Feed Fuel Injector Cleaning
Add to cart
Quick view

Side Feed Fuel Injector Clean and Flow Test

SKU: CleanFlow-SideFeed
$25.00
Add to cart
Quick view

RX8 & WRX Modification

SKU: RX8Mod
$25.00
ultrasonic fuel rail cleaning
Add to cart
Quick view

Fuel Rail Ultrasonic Cleaning

$25.00
tuning fuel map
Select options
Quick view

GDI Injector Custom Flow Testing Tuning Data

SKU: CleanFlow-GDI-1
$30.00
GDI Injector Cleaning
Select options
Quick view

GDI Injector Cleaning and Flow Testing

SKU: CleanFlow-GDI
$35.00
Hose End Cleaning
Select options
Quick view

Hose End Type Injector Cleaning and Flow Testing

SKU: CleanFlow-HoseEnd
$22.00
P.O. Box 1547 Blackwood, NJ 08012
Phone: (856) 346-2778
SMS / Text: (856) 345-9627
Contact Us
Useful links
  • Login/Register
  • Core Rewards
  • Online Shop
  • Knowledge Base
  • Application Guide
  • FAQs
I-R Info
  • Privacy Policy
  • Terms & Conditions
  • Warranty
  • Contact Us
  • My Account
INJECTOR-REHAB 2020
  • Menu
  • Categories
  • Injector Cleaning
  • Pintle Caps
  • O-Rings
  • Filters
  • Grommets and Other
  • GDI & Piezo Components
  • Rebuild Kits
  • Connectors & Adapters
  • Bulk Components
  • Injector Cleaning Supplies
  • Injectors
    • New Injectors
    • Refurbished Injectors
      • Automotive
      • Marine Injectors
      • Nissan Re-Coiled JECS
  • KGParts Products
    • VW Fuel Systems
    • BMW Motorcycle
    • Mazda RX7 Top Feed Fuel Rails
      • Mazda RX8
      • Other Rotary
      • RX7 86-91 (FC)
      • RX7 93+ (FD)
    • Misc KGParts Items
    • Pro-Jay Intake Manifolds
  • Home
  • Videos
  • Core Rewards
  • Shop
  • Knowledge Base
  • FAQs
  • Fuel Injector Application Guide
  • Contact Us
  • Login / Register
Shopping cart
Close
Sign in
Close

Lost your password?

No account yet?

Create an Account